FashionMargoGirl: пополнение в индустрии DIY

DIY: Button Statment Rings

It’s September and that means it’s time to add another statement piece to your collection…. obviously! I heart almost every piece Nicole Richie designs for House Of Harlow 1960, especially her oversized rings. As amazing as these rings are they’re also an easy DIY. My friend Jenni, from I Spy DIY, did a project a few months back where she transformed buttons into earrings. #SuperFab This got me thing…let’s transform buttons into statement rings!

Buttons, buttons everywhere!! Someone please tell me why I’ve collected all these buttons.

Materials: Buttons, Clippers, Glue, Rings With Flat Tops (available at the jewelry supply store)

Use your clippers to remove the shank from the back of the button.

Once you’ve made the back of the button flat, use an ample amount of glue to secure the ring to the back of the button.

Here’s another hint: If you can’t find a flat ring base, Ring Pops are a fun alternative. After you’ve removed the candy and cleaned the ring base, grab your Kylon spray and paint it.

Once the base has dried, glue on the button.

I now thing I have enough new statement rings to get me through the month.

diy: Lanyard Double Chain Bracelet

This project brings back memories, in more than one way. 1) I loved lanyard when I was a kid, and I clearly remember making sooo many keychains and bracelets. 2) This DIY reminds me of S&P's first ever project, the Braided Chain Bracelet, from last summer. And 3) ...Well, my entire bedding set during my Freshman year of college were these exact colors. My comforter was reversible neon green and bright blue, and I even had hangers and towels in the same colors. By the time I graduated I was more into the darker jewel tones, but I still can't resist a good pop of color.

Supplies:

- Chain, twice the length of your wrist

- Lanyard, 1-4 colors

- Scissors

- Jewelry pliers

- Jump rings

- Toggle or clasp closures

1) Cut two strands of lanyard, about 60 inches each

2) Fold both strands in half and tie a knot. Separate the strands like above; I used two colors so it'd be easy to follow along.

3) Fold the chain in half. Insert the two middle strands - one of each color/side - into the center link of the chain.

4) Take the outer blue strand and insert it directly through the next empty link. It should end up "behind" the chain.

5) Fold it over the chain and towards the left, and insert it through the next empty link. Keep repeating, and you'll end up with something like this. Make sure you pull pretty tight; the slippery finish of lanyard makes it likely to unwravel and loosen from the chain.

The chain might be kind of wonky while you'r doing this, but just keep on going. You can straighten everything out later.

6) Repeat until you reach the end of the chain.

7) Take the inner blue strand, and bring it under the chain and through the next empty link. I placed an arrow where the first "stitch" was.

Closeup.

8) Keep repeating until you reach the end of the chain. You'll want to pull tight like you did with the first strand, but make sure not to pull TOO tight. You'll later be weaving the neon green through the blue lanyard, in order to connect the two sides.

9) Take the outer strand of the second color - in this case neon green - and start weaving the lanyard through the chain. You're essentially repeating steps 4 and 5.

10) Repeat until you reach the end of the chain.

11) Taking the inner/second neon green strand, insert it through the next empty chain link. From here on you'll be inserting it through the adjacent blue stitch, then bringing it back into the chain.

I found it was a lot easier to work with upside down!

Green goes through the blue...

And then down through the next empty link.

Pull tight, and repeat.

12) When you're done with both sides, tie the strands off with tight knots, and trim.

13) Add the jump ring and bracelet closure of your choice.

14) Go back to the other side of the bracelet, unwravel the first knot you made and cut the two loops. Tie them off with tight knots and trim.

15) Add the other half of the bracelet closure.

Finished bracelet.

I had to make a black and gold version...the classic color combo that I love so much. The black lanyard kind of reminds of me patent leather, actually.

I'd really recommend using a thick, heavy duty curb chain for this. However, keep in mind that this probably means it's a bit hard to cut. You might need a wire cutter or jewelry pliers - but probably a wire cutter - to trim the chain. If you get the chain cut in a hardware or craft store, I'd also recommend maybe having the employee further trim the chain for you in the lengths that you need (again, twice the length of your wrist), since you're there anyway. I lucked out and happened to have two strands of this chain left in the length I needed...but I know this chain is impossible to cut with a pair of scissors or pliers. In other words: don't hurt yourself trying to cut this really heavy chain!

I'll really want to try this with leather cord in different colors...or just more lanyard. Maybe make some in fall colors? Mustard yellow, eggplant purple and burnt orange sounds good to me.

I'm doing another Q&A, so if you have any questions - DIY or otherwise - just leave a comment or send me an e-mail at kirsten.studsandpearls@gmail.com!

Also, if you'd like to be added to the mailing list, you can also leave a comment with your e-mail address, or also send me a message at kirsten.studsandpearls@gmail.com. I send out an e-mail whenever I post a new project, so this is useful if you're not always on Facebook or Twitter.

xo,